Wszystkie opinie klientow o Color N Drive 9H Ceramic Coating

After I opened the box (unsealed and opened) possibly due to customs? There was no coated sponge in the box. Not a big deal but I expected it.

La moto la tengo ya un mes y no se ensucia, el agua y polvo los repele excelente. La pintura ha quedado muy brillante y los plásticos también han funcionado con el producto, con un negro muy sólido sin manchas.

It makes the paint and chrome look DEEP & EXTREMELY SHINY! This stuff really works! I did it on my 2005 victory vegas! Put it over the whole bike except seats & tires. It goes on windshield & I polished the heck out of my aluminum wheels until they wouldn't get anymore shiny & I put this ceramic coating on them & I WONT HAVE TO POLISH ALUMINUM WHEELS AGAIN!!! THEY LOOK AS GOOD AS FRESH CHROME! THIS STUFF IS THE WAY TO GO! JUST MAKE SURE UR VEHICLE IS SPOTLESS! Cause once it's under ceramic its gonna show forever! DO NOT LEAVE CERAMIC ON LONGER THAN 2-3 MIN! BUFF IT & THE MORE U BUFF IT THE SHINIER IT BECOMES THEN IT DRIES & HARDENS 12-24 HRS LATER!

This is a truly amazing product, very fast delivery.

Short term results are very good so far. Makes maintenance washes a breeze. Will have to see how long it lasts to give a long term recommendation. As many others have stated, success for this ceramic as well as any others is in the prep work and OCD attention to detail during ceramic application. I did use this on the wheels and in fact found them much more fool proof. Good results so far on the wheels. General sequence i followed: 1) Regular wash 2) Iron-x (i applied with vehical wet) 3) Sprayed diluted solution of degreaser, rubbed in, and rinsed 4) Wash with dish soap (AJAX) 5) Clay Bar then rinsed 6) Compounded with DA using Mequiars 7) Sprayed and wiped with 25% alcohol (mixed with distilled water) and dried 8) Applied Ceramic small sections/panel at a time (split hood into 3 sections) FOLLOW INSTRUCTIONS On the ceramic application, applied prep spray, with prep spray STILL wet, I used the supplied foam applicator being generous and coating evenly with horizontal and intersecting vertical passes, waited about 1 or 2 minutes (DO NOT LET THIS EVEN GET CLOSE TO DRYING), sprayed MF towel with distilled water (damp not soaking wet),and push/final spread product, then IMMEDIATELY used separate MF towel to buff and wipe remaining product off (critical that you get this step 100% otherwise will be left with high spots that have to be machine compounded off). I have applied this product to two vehicles and using the above method. There were two small spots on the first vehicle that I didn't get off fully and both were instances where the damp cloth used to push/spread the product drifted just beyond my intended working area (where separate body panels meet) and I failed to catch it and remove it.

Great quality and super fast shipping coming from Turkey. dirt and water roll right off of the surface of the car, Highly recommended

Amazing product. I do not know how it is compare to other ceramic coating but it did the work! The below photo was taken after a guy scratched my car with his. I just took a wet towel and it all disappeared!!

Great product

As many others have mentioned, this product came with little to no instruction. The little piece of paper with a QR code takes you to their product page, not the "detail instruction page" they had you believe. If you have done your research and still feel confident about your DIY skill to try this, make sure you test the pre-treatment spray bottle that come with this kit. After hours of preparing my SUV, which involve pressure wash -> tar removal -> clay bar -> buff out scratch with compound -> wash and dry again -> wipe down with alcohol, here comes the time to spray on the pre-treatment. Mine just drip down my hand/cloth and "sprayed" a couple drops on the car instead of mist. Had to buy another pray bottle from the drug store. wipe down the SUV one more time and try again. This time the application was easy, but buff was not. That buffing towel just shred fuss everywhere and make a mess. I ended up just waxed and called it a day. Updates: Took a lot of time and finally did the top of the car. Then their customer service reached out to me. They sent a detail instruction on how to use this product, and tried to make it right. Unfortunately, I do not have the time to try it again now, so I got a refund instead. Changed my review based on customer service and the result on the top of the car looks promising. I may try again when I have the time, but this stuff is just sitting on my shelf for now.

It's a good ceramic coating, however, besides the fact Color N drive send you a very nice e beautiful pack, the information about using the product is very poor. You will need to email them to ask about how to use it safely, if you don't have experience on aplying coatings. It seems simple, but it's not !